Pelican-Hardigg™ Rotomolded Rackmount Case Options

Pelican-Hardigg™ offers a broad range of standard options for our Rackmount shipping cases. These elements, described below, allow you to adapt our cases to a wide variety of transit applications.

Rackmount Case Options for Classic (DE) Rack, SuperMAC™ & MAC Rack™

	Airtight / Watertight Includes PRV (pressure relief valve) and gasketing hardware to safely maintain correct pressure differential. Manual release button is recessed below cover rim. Test pressure range is +/- 0.25 PSID (18 mb).

	Casters Caster mounting system enhances the bottom panel strength of rack cases, while providing the same button release convenience of the FastClip™ mounting plate system found on Hardigg's single-lid cases. Available in removable or fixed 3.5" or 5" wheel diameters. Includes four casters, two machined aircraft aluminum extrusions, and mounting hardware installed on the case bottom.

	Edge Casters Set consists of (2) caster/ wheel housings, permanently installed into the edge of the case shell. This option is standard on SuperMAC and MAC Rack Cases with a 5" lid.

	Caster Storage in Lid Removable casters are securely stored in lid using Pelican FastCliptm (storage plate) mounting plate system (for 5" lids only (127 mm).

	Custom Stenciling Per MIL-I-43553. Available colors are Black, White, and Yellow. Listed below are popular combinations of the case color along with the corresponding ink color. One ink color per case. If not specified Pelican will choose color. Pelican reserves the right to choose the stencil text or graphic size, font and location.

	Card Holder Metal holder for shipping-card riveted to the exterior of case. Two sizes: 2-3/8" x 5-3/8" 4.0 x 6.0"

	Metal or Comfort Grip Handles Available in plastic, zinc-plate yellow-chromate, ROHS compliant silver zinc, or stainless steel.

	ID Plate I.A.W. MIL-P-15024, Type H, Style IV, Size 10.4 x 4.0 x .020" (102 x 102 x 0.5mm) thick aluminum, fastener attached to your case. Text font is News Gothic Bold.

	Front Labels To assure that lids are replaced in the proper orientation. A set of two "front" labels is affixed to the case, one on the midsection and one on the lid.

	Standard Labels Up Arrows Delicate unit Handle with Care / Reusable Container

	Coupling Catches Elastomeric devices to couple vertically stacked containers to prevent accidental tip over.

	Dessicant Basket Designed to hold MIL-D-3464 bagged desiccant. Each basket comes complete with spanner nut, washer and retained gasket. Hole through cover and flange are provided for safety wiring and inspector seal. Inside dimensions: 3.37 x 12". Outside dimensions: 4.5 dia x 12.75". Installation hole in container is 4.015" diameter. Also available in 7.75, 14.75 and 17.75" depths.

	Humidity Indicator Indicates 20%, 30%, and 40% relative humidity ranges. Three-part face changes color when inside humidity exceeds the indicated level. As humidity decreases, the indicator resets for future use. Recommended for airtight cases only.

	Lid Hangers Used to store lids conveniently on side of case when case is open. A set of four hangers for two lids. This option comes at no extra charge.

Lid Storage Pouch
Zippered pouch for storing cables and accessories in front or rear lids. Comes mounted in 5" lids. Three sizes:

10.0 x 22.0 x 2.5"
16.0 x 22.0 x 2.5"
18.0 x 18.0 x 2.5"

	Leg Kit (Chair or Table)

Lockable Cable Catch (1 set of 4)
Allows the case to be padlocked shut. The cable is made of tamper resistant aircraft steel. Qty (2) required per lid, comes in a set of (4).

	Lifting / Tie Down Rings Welded rings provide hoisting and tie-down attachment points with 2" (51 mm) diameter clearance for hooks. They're spring-loaded and pivot 180°. Available in plated steel or stainless steel.

	Removable Rack Frame The Rapid Rack option adds a simple Lock 'N Load quick-latch system and sliders to unlock the internal rack frame for smooth separation. Pulled like a drawer, the entire rack frame slides out completely for in-the-field usage and connection to other equipment or for easier cable installation. Available for Classic or SuperMAC Rack cases.

	Hardware - Stainless Steel Upgrade - Standard zinc-plated yellow chromate hardware catches, strikes, handles, hinges) is replaced by stainless-steel (clear passivated finish). Recommended for applications where standard zinc plate or zinc alloy finishes are not suitable, such as excessive saltwater or chemical environments.

	1/8" Wider Frame Used when extra clearance is necessary, usually to accommodate slides. Requires slotted mounting holes in attaching bezel of equipment to be mounted.

	Bottom Support Rails Two each support rails used to support equipment while installing heavy loads.

	Adjustable Verticle Side Supports Two each 2.0 x 2.0 x 1/8" (51mm x 51mm x 3mm) aluminum-angle, vertically-adjustable support rails used to support equipment while installing heavy loads.

	Adjustable Horizontal Side Supports Aluminum-angle, vertically-adjustable support rails used to support equipment while installing heavy loads.

	Bezel Plate Blank bezel plates in 16 gauge aluminum. Flanged for strength. Brushed black anodized finish. Available in 1U, 2U, 3U, and 4U heights. See our Rackmount Accessories page.

	Drawers 19" rack-mountable drawers are 14 inches (356 mm) deep and keylockable. Complete with drawer-slides. Available in 2U, 3U, and 4U unit heights U=1.75") (U=44.45mm)

	Keyboard Tray Accommodates standard size keyboard. 24" (610 mm) wide, 12" (305 mm) deep. Attaches to case front catches.

	Shelves (Fixed or Sliding) Shelves can be removed and customized to accommodate non rackmountable equipment. Also see our standard sized shelves on the Rackmount Accessories page.

	Panel Screws with Washers (50 ea) Used for mounting rack units, drawers, and blank bezel plates. #10-32, X 0.75 Large screw with nonmetallic washers for scratch protection.

	Rack Slides These compact solid-bearing steel slides may be used to mount equipment directly into rack, or to mount drawers or shelves. Sold in pairs. Available in standard duty, 85 pound capacity.

Extended Load Kit
For extra-heavy loads. For rackmount cases with more than 170 lb. (77 Kg) of packaged equipment, sixteen elastomeric shock mounts are used instead of the standard eight. Vertical metal wall stiffeners are added to the case body to retain dimensional control of the two openings and ensure that the covers can easily go back on the case body and latch properly. Four delta lifting/tie-down rings are also installed to provide mechanical lift accessibility.

Rackmount Case Options for PRO Racks

	Airtight / Watertight Includes PRV (pressure relief valve) and gasketing hardware to safely maintain correct pressure differential. Manual release button is recessed below cover rim. Test pressure range is +/- 0.25 PSID (18 mb).

	Casters Caster mounting system enhances the bottom panel strength of rack cases, while providing the same button release convenience of the FastClip mounting plate system found on Hardigg's single-lid cases. Available in removable or fixed 3.5" or 5" wheel diameters. Includes four casters, two machined aircraft aluminum extrusions, and mounting hardware installed on the case bottom.

	Custom Stenciling Per MIL-I-43553. Available colors are Black, White, and Yellow. One ink color per case. If not specified Hardigg will choose color. Hardigg reserves the right to choose the stencil text or graphic size, font and location.

Card Holder

Card Holder

Metal holder for shipping-card riveted to the exterior of case. Two sizes:

2-3/8" x 5-3/8"
4.0 x 6.0"

	ID Plate I.A.W. MIL-P-15024, Type H, Style IV, Size 10.4 x 4.0 x .020" (102 x 102 x 0.5mm) thick aluminum, fastener attached to your case. Text font is News Gothic Bold.

	Front Labels To assure that lids are replaced in the proper orientation. A set of two "front" labels is affixed to the case, one on the midsection and one on the lid.

	Coupling Catches

	Hardware - Stainless Steel Upgrade - Standard zinc-plated yellow chromate hardware (catches, strikes, handles, hinges) is replaced by stainless-steel (clear passivated finish). Recommended for applications where standard zincplate or zinc alloy finishes are not suitable, such as excessive saltwater or chemical environments.

	Rear Rack Frame

	Bezel Plate Blank bezel plates in 16 gauge aluminum. Flanged for strength. Brushed black anodized finish. Available in 1U, 2U, 3U, and 4U heights. See our Rackmount Accessories page.

	Drawers 19" rack-mountable drawers are 14 inches (356 mm) deep and keylockable. Complete with drawer-slides. Available in 2U, 3U, and 4U unit heights U=1.75") (U=44.45mm)

	Shelves (Fixed or Sliding) Shelves can be removed and customized to accommodate non rackmountable equipment. Also see our standard sized shelves on the Rackmount Accessories page.

	Panel Screws with Washers (50 each) Used for mounting rack units, drawers, and blank bezel plates. #10-32, X 0.75 Large screw with nonmetallic washers for scratch protection.

	Extra Threaded Rack Clips

813-513-9910

sales@cases2go.com

Options

Rackmount Case Options for Classic (DE) Rack, SuperMAC™ & MAC Rack™

Rackmount Case Options for PRO Racks

Stay in Touch!

Corrosion Control Products